HSC & PWM Tutorial
22
pages
English
Documents
Cet ouvrage est disponible dans votre offre d'abonnement
22
pages
English
Documents
Cet ouvrage est disponible dans votre offre d'abonnement
Publié par
Langue
English
HSC & PWM Tutorial HSC & PWM tutorial Table of Contents TABLE OF CONTENTS ............................................................................................2 INTRODUCTION........................................................................................................3 STEPPER AND SERVO MOTORS ..........................................................................4 PWM REGISTER MAP..............................................................................................5 CONFIGURING THE PWM FUNCTIONS.............................................................5 CONFIGURING THE PWM OUTPUTS............................................................................5 FUNCTION ...................................................................................................................6 HSC OUTPUT FUNCTION8 HSC (High Speed Counter)....................................................................................8 STEPPER FUNCTION...................................................................................................10 PROGRAMMING EXAMPLES..............................................................................12 PWM FUNCTION PROGRAM......................................................................................12 I/O Configuration.................................................................................................13 Ladder Logic ...
Voir
Publié par
Langue
English
HSC & PWM Tutorial
HSC & PWM tutorial
Table of Contents TABLE OF CONTENTS ............................................................................................2 INTRODUCTION........................................................................................................3 STEPPER AND SERVO MOTORS ..........................................................................4 PWM REGISTER MAP..............................................................................................5 CONFIGURING THE PWM FUNCTIONS .............................................................5 C ONFIGURING THE PWM O UTPUTS ............................................................................5 F UNCTION ...................................................................................................................6 HSC O UTPUT F UNCTION ............................................................................................8 HSC (High Speed Counter)....................................................................................8 S TEPPER F UNCTION ...................................................................................................10 PROGRAMMING EXAMPLES ..............................................................................12 PWM F UNCTION P ROGRAM ......................................................................................12 I/O Configuration.................................................................................................13 Ladder Logic Programming ................................................................................14 Screen Editor Programming ................................................................................15 S TEPPER F UNCTION ...................................................................................................17 I/O Configuration.................................................................................................17 Ladder Logic Programming ................................................................................18
www.imopc.com
2
Introduction The i³ has a two channel PWM output that can be configured into 3 different modes. Possible configurations are: 2x High Speed Counter (HSC) function, 2x Pulse Width Modulation (PWM) function (or a mix of the two) and 1x Stepper function. This output function allows the i³ to be used in motion control applications by operating a stepper motor (through its driver) to a high level of accuracy. If the PWM / HSC output function is used then the i³ can control two axis or, a single Stepper motor axis. The purpose of this tutorial is to demonstrate the Pulse Width Modulation output function of the i 3 . Only the models with transistor outputs support the PWM function. In this tutorial we will demonstrate all the functions related to the PWM function and demonstrate the i 3 controlling a Stepper Motor following a pattern.
©IMO Precision Controls LTD
3
HSC & PWM tutorial
Stepper and Servo Motors A stepper motor rotates in defined steps depending up on the resolution of the motor. For example an 8 bit digital controller will give a resolution of 360 º / 256 giving a resolution of 1.40625. Given this level of accuracy stepper motors are widely used in motion control and positioning applications. Attached to the shaft of the motor is a series of permanent magnets and around the body there is a series of coils that creates a magnetic field when a charge is applied. To make the shaft rotate the coils must be pulsed on and off constantly, the sequence in which coils are switched on determines the direction of the motor. Stepper motors could be used with an encoder to determine the exact real position of the shaft however they are generally used in an “open-loop control system. A servo motor is similar to standard electric motor in that it doesn’t have predifined steps and is less complicated in terms of magnets to coils. The accuracy of a servo motor depends on the feedback system and unlike Stepper motors, a Servo motor must be implemented in a closed loop system. With the motor being less complicated the Servo Drive controller circuitry will be a lot more complex than that of a Stepper motor.
www.imopc.com
4
PWM Register Map All three PWM output functions use the same registers but their use depends on the motor type connected.
%AQ1 PWM1 Duty Cycle HSC1 Start Frequency %AQ2 (32-bit) Preset Value Run Frequency %AQ3 PWM2 Duty Cycle HSC2 Accel Count %AQ4 (32-bit) Preset Value (32-bit) %AQ5 PWM Prescale Run Count %AQ6 (32-bit) (32-bit) %AQ7 PWM Period Decel Count %AQ8 (32-bit) (32-bit) %Q1 Run %I30 Ready/Done %I31 Error
Configuring the PWM Functions The PWM outputs are configured in the Config I/O menu and then the registers shown are manipulated. Configuring the PWM Outputs To set up the PWM function click on the Config I/O icon or select the option from the drop down menu. To enable the two PWM outputs select the appropriate function It is possible to set up the PWM function in the I/O config menu, but in this tutorial we will use registers.
©IMO Precision Controls LTD 5
It is only possible to select Stepper on Q1 as it uses Q2 registers. Q2 will only then be a digital direction bit.
HSC & PWM tutorial
Function Having selected Q1 or Q2 as a PWM output we now are required to use the registers as shown below.
%AQ1 PWM1 Duty Cycle (32-bit) %AQ2 %AQ3 PWM2 Duty Cycle (32-bit) %AQ4 %AQ5 PWM Prescale %AQ6 (32-bit) %AQ7 PWM Period %AQ8 (32-bit) Both outputs are configured to the same frequency, while the pulse width can be adjusted on each output independently. The PWM functions require three parameters (%AQ registers) to be set for operation. These parameters may be set whilst in run-time, that is the user can enter a new value through the HMI. Prescale This sets the resolution of the PWM output. Fore most applications this can set this to 15, which will give a resolution of 1 microsecond in terms of period and duty cycle. The frequency of the PWM output is calculated using the following formula:
Frequency = Period This value (%AQ7-8) sets the period of the output signal by specifying the number of internal PWM counter counts before the cycle is reset (larger count results in a smaller frequency). The duration of each count is determined by the pre-scale value. This parameter affects the Period of both PWM outputs The formula above shows how the pre-scale and period create an output frequency. For example if the PWM were set for 1 microsecond resolution, a value of 20,000 would result in a 50 Hz output.
.
www.imopc.com
6
This value sets the period of the output signal. This value determines the width of the output wave. A longer period results in a smaller frequency. The numeric value entered here is the number of counts for the pulse width. The duration of each count is set by the value of the re-scaler.
Duty Cycle Count -This value (PWM1: %AQ1-2, PWM2: %AQ3-4) sets the width of the output signal by specifying the number of internal PWM counter counts that the output is maintained high. The duration of each count is determined by the pre-scaler value. Each PWM channel has its own duty cycle count parameter.
Duty Cycle
The duty cycle determines the amount o time the output wave spends high. If the period is set to 1000 and the duty cycle is set to 500 it would result in a duty cycle of 50 percent. A duty cycle value of 250 would result in a duty cycle of 25 percent
At controller power-up or during a download, the PWM output is maintained at zero until both the Period (count) and the Duty cycle (count) are loaded with non-zero values. When the controller is placed in stop mode, the state of the PWM outputs is dependent on the PWM State on Controller Stop configuration. This configuration allows for either hold-last-state or specific pre-scale, period and duty cycle counts. Specifying zero for either the period or duty causes the PWM output to remain low during stop mode. Note that the nominal output driver turn-on-time delay (to reach 50% output) is 25 microseconds. Therefore, this limitation should be considered when determining both the minimum pulse width and the duty cycle accuracy of the application.
©IMO Precision Controls LTD
7
HSC & PWM tutorial
HSC Output Function HSC (High Speed Counter) When either Q1 or Q2 is configured for HSC operation, HSC1 or HSC2 totalize functions are extended to allow respective direct output control based on a comparison of the current count and a preset value (PV). See totalize in the HSC section above for more information. Totalize In totalize mode, the accumulator is simply incremented each time the input transitions in a specific direction. Totalize mode is configurable to specify the edge (rising or falling) on which the accumulator is incremented.
Rising Edge Signal Falling Edge Signal Three different options are available to reset the current count. They are: • Configured reset value When configuring the Totalize function, a value may be specified under the Counts per Rev column. When the Totalizer accumulator reaches this value -1, the accumulator will reset to zero on the next count. Specifying zero for this value allows the Totalizer to count through the full 32-bit range before resetting. • Ladder control Setting registers %Q17-20 reset HSC1-4 (respectively) with no additional configuration. When these registers are asserted, the associated Totalizer accumulator is reset and held at zero (level sensitive). See also Section 10.6. • Direct digital input control (HSC1 and HSC2 only) HSC3 (%I11) and HSC4 (%I12) may be configured as hardware digital reset signals for HSC1 and HSC2 respectively. To enable these inputs as reset signals, specify the type as Totalize Reset (note that the corresponding Totalize HSC must be previously configured before this option is available). The direct digital reset controls are edge sensitive with the edge polarity configurable.
www.imopc.com
8
Maximum direct digital reset latency is 100 µs. The totalize function also supports an option which compares the current accumulator value with a supplied Preset Value (PV), which is provided through a %AQ, and drives a physical digital output based on the that comparison. • This option (available for HSC1 and HSC2 only) drives Q1 or Q2 output point (respectively) once the associated Totalizer accumulator reaches (or exceeds) the PV value. To enable this function, the corresponding PWM function output (Q1 or Q2) must be configured for HSCn Output . Note: Q1 and Q2 are PWM function outputs that may be configured independently as one of the following: standard digital output, PWM, HSCn or stepper output.
©IMO Precision Controls LTD
9
HSC & PWM tutorial
Stepper Function When the output Q1 is configured for Stepper, the stepper function is enabled at the Q1 output. Only one stepper function and output is available. Q2 is then limited to only a direct digital output, which could be used to signify direction. The Stepper function requires all five parameters (%AQ registers) to be set for operation. These parameters may be set at whilst the i 3 is in run mode but are ‘latched’ when the stepper function is in operation.
%AQ1 Start Frequency %AQ2 Run Frequency %AQ3 Accel Count %AQ4 (32-bit) %AQ5 Run Count %AQ6 (32-bit) %AQ7 Decel Count %AQ8 (32-bit) %Q1 Run %I30 Ready/Done %I31 Error • Start Frequency (cycles per second) (%AQ1) This value sets the frequency for the first cycle during the acceleration phase and the frequency of the last cycle during the deceleration phase. When an acceleration or deceleration count is specified, the Start Frequency must be greater than 0 and must not exceed the run frequency or an error is generated. • Run Frequency (cycles per second) (%AQ2) This value sets the frequency for the last cycle during the acceleration phase, the consistent frequency during the run phase, and the frequency of the first cycle during the deceleration mode. The Run Frequency must be greater than 0 and must not exceed 5000 cycles/sec. or an error is generated. • Acceleration Count (%AQ3-4) This value sets the number of cycles to occur within the acceleration phase. The frequency of the cycles within this mode will vary linearly between the specified Start and Run frequency. The acceleration count must not equal 1 or an error is generated. Setting this value to zero disables this phase. • Run Count (%AQ5-6) This value sets the number of cycles to occur within the run phase. The frequency of the cycles within this mode is constant at the specified Run frequency. The Run count may be any value. Setting this value to zero disables this phase.
www.imopc.com
10
• Deceleration Count (%AQ7-8) This value sets the number of cycles to occur within the deceleration phase. The frequency of the cycles within this phase will vary linearly between the specified Run and Stop frequency. The Deceleration count must not equal 1 or an error is generated. Setting this value to zero disables this phase. The stepper function provides two Boolean registers to provide stepper status • Ready/Done (%I30) A high indication on this register indicates the stepper sequence can be started (i.e. not currently busy). • Error (%I31) A high indication on this register indicates that one of the analogue parameters specified above is invalid or the stepper action was aborted before the operation was complete. This register is cleared on the next start command if the cause of error was rectified. To start the stepper function, one discrete register is required (%Q1). This register must remain set to logic ‘1’ in order to complete the entire cycle. Clearing this register before the cycle is complete aborts the step sequence and sets the error bit. Note that setting the PLC mode to Stop while the stepper is in operation causes the stepper output to immediately drop to zero and the current stepper count to be lost. Please note that stepper output level may cause damage or be incompatible with some motor driver inputs. Please always consult the drive documentation to determine if output level of the i 3 and type is compatible.
©IMO Precision Controls LTD
11
